AUTOOL CT160 Ultrasonic PetrolCar Fuel Injector Heating Cleaning&Tester Machine

AUTOOL CT160 Car Motor Fuel Injector Heating Cleaning &Tester Machine Ultrasonic Cleaner Gasoline Fuel Injector 4-Cylinders 220V. AUTOOL CT160 Fuel injector diagnostic and cleaning equipment is a mechatronics product that combines ultrasonic cleaning technology and microcomputer oil pressure closed-loop control cleaning and detection technology. This product simulates various operating conditions of the engine and cleans and inspects the fuel injectors of various automobiles and motorcycles. This equipment is the necessary and preferred equipment for the automobile and motorcycle repair and maintenance industry, research and teaching, and training departments. Ultrasonic cleaning: Ultrasonic cleaning can be performed on single or.

Multiple injectors at the same time, which can remove the attachments and internal. Uniformity detection: to detect the uniformity of the injection volume of each. Atomization observation: Using the background light, you can observe the.

Spray atomization situation of the nozzle in a comprehensive and careful manner. Tightness test: It can detect the tightness and dripping of the fuel injector. Fuel injection volume detection: It can detect the fuel injection volume of the. Fuel injection nozzle under specific working conditions such as the same time. And the same number of times.

[Ultrasonic Cleaning with Heating the Fluid]: Different from others, AUTOOL CT160 is able to heat the cleaning fluid, which can improve a lot on cleaning effect. With that advantage, ultrasonic cleaning can be more powerful to remove the attachments and internal blockages on the injectors.

[9 Kinds of Fuel Injector Tests]: AUTOOL CT160 Fuel injector Cleaner is capable of various testing, including 2-idle speed test, 3-medium speed test, 4-high speed test, 5-accelerating test, 6-variable speed test, 7-leakage test, 8-idle spray test, 9-medium spray test, 10-high spray volume test. [Compact/Lightweight/Portable]: AUTOOL CT160 Fuel injector Cleaner only weighs 8KG, allowing to carry around. With 1300ML large capacity ultra cleaning tank, all injectors can be cleaned at one time, which save much time and more efficient. [Environmental Friendly& Widely Use]: The used cleaning fluid and testing fluid can be easily recovered. Support most of the automobile and motorcycles in the market.

Applicable voltage is compatible with 110V or 220V. Pour in the cleaning fluid &. Place the fuel injector in the.

Connect the pulse signal wire &. Pour in the test liquid, install the.

Fuel injector to the fuel distributor. And fix it to the main unit by bolts. Test if the fuel injector is.

Please use special nozzle cleaner. In the absence of test liquid: industrial alcohol can be used for testing. The test agent must not contain corrosiveness, and do not add corrosive liquids for testing. Don't confuse test agent and cleaning agent. PWM pulse width0 20.0ms step0.1ms.

Injection times09900 times, step 100ms. 1pc AUTOOL CT160 Fuel injector diagnostic and cleaning Cleaner Machine main unit. 4pc Motorcycle top oil inlet connectorf10mm. 4pc Motorcycle top oil inlet connectorf11mm.

4pc Motorcycle top oil inlet connectorf10.6mm. 4pc Car top oil inlet connectorf10.6mm&13.4mm. Check whether the fuse on the bottom of the right side of the machine is damaged. If it is damaged, please replace the fuse (AC 250V/5A). Oil leakage at the oil separator assembly. Oil leakage at the oil separator, please check whether the installed "O" ring is matched, and check whether it is deformed or damaged. If it is not matched or damaged, please replace it;The two black adjusting screws should not be too tight, too tight will also cause oil leakage of the oil separator. The oil pressure drops slowly. The oil pressure cannot drop to zero within 1 to 2 minutes, and you can use the hex wrench to adjust the relief valve counterclockwise.

The buzzer sounds long without oil pressure. The machine has a lack of oil alarm function. At this time, you must press the [Run] key to restart the oil pump.

Must be pressed'Drain key' twice to drain test solution completely. The solenoid valve of the machine has an automatic shut-off function within 15 seconds; more liquid in the glass tube may require multiple drains. The amount of cleaning and test solution added. When adding cleaning fluid, the cleaning fluid in the ultrasonic box should not exceed the connection port of the fuel injection nozzle; when adding test fluid, the testing fluid should not exceed two-thirds of the glass tube level display.

Problems with cleaning and testing 4 injectors. You need to find the problematic nozzle and replace it with another normal nozzle for cleaning.

If there is no problem with the fuel injector, one of the pulse lines is damaged. There are 6pcs impulse lines, and each impulse line needs to be tested separately. If all 6pcs pulse lines can be used normally, this is the problem of the fuel nozzle. Welcome to our store, wish you have happy shopping time! Feedback is the best support for our store.

Feedback, so that we can know the problem and try our best to meet your requirements. We apologize for the late reply during the holidays. We are a customer-oriented company and your feedback is highly important to us, so please let us know. The item "AUTOOL CT160 Ultrasonic PetrolCar Fuel Injector Heating Cleaning&Tester Machine" is in sale since Thursday, May 20, 2021. This item is in the category "Vehicle Parts & Accessories\Garage Equipment & Tools\Diagnostic Equipment & Tools\Other Diagnostic Service Tools".

The seller is "autool-2019" and is located in shenzhen. This item can be shipped worldwide.

Brand: Autool
Warranty: 3 Year
Type: Injector Tester
Country/Region of Manufacture: China
Weight: 8.6 kg
Model name: CT160
Manufacturer Part Number: MIC10-5
Non-Domestic Product: Yes
Vehicle Type: Motorcycle
Custom Bundle: No
Modified Item: No
Type 2: Ultrasonic Cleaner
Power supply: AC220V10%
Frequency: 50HZ0.5
Relative Humidity: <85%
Environment Temperature: 0°C~40°C
External magnetic field strength: <400A/m
Tank capacity: 1300ml
Range of rotation: 0~ 7500r/min
PWM pulse width: 0~ 20.0ms step0.1ms
Time: 0~ 20min
Cleaning Frequency: 40KHz
Cylinder Volume: 180ml
Injection Times: 0~9900 times, step 100ms
System Pressure: 0~0.6Mpa
UItrasonic Cleaning Power: 70W
Main Unit Dimensions: 292x260x273mm
Package Dimensions: 340x295x360mm
Unit Quantity: 1
Unit Type: Unit
OBD Interface: CAN